GPS Tracking for Forklift & Material Handling Fleets
Forklift dealers, rental operations and material handling fleets need to know where every unit is and how many hours it has run. Mobile Fleet Solutions installs hard-wired trackers that report both.
- Trusted by fleet leaders
- 25+ years helping fleets
- Based in Gainesville, GA
- Serving 10 states

Run Hours You Can Bill and Service From
Wired asset trackers are primarily used for equipment, so you can monitor:
Location of every forklift and machine
Run-time hours for billing your customer
Run-time hours for scheduling maintenance
Ignition and run-hour sensing through GPIO inputs
Tamper alerts and back-up reporting
Alerts for unexpected movement or relocation
This data helps fleet managers reduce losses, improve utilization, and maintain better control over high-value equipment.
The AS11 Hard-Wired Asset Tracker
A rugged LTE asset tracker recommended for depot installs where continuous run-time reporting and sensor integration are required.
- IP68-rated enclosure for harsh environments
- Rechargeable internal battery for safe shutdown, tamper alerts and back-up reporting
- GPIO inputs for ignition, run-hour sensing and door/tilt sensors
- Wired, permanent installs on forklifts and other heavy assets
Mobile Fleet Solutions performs the hardwiring, GPIO mapping and commissioning, and is a member of MHEDA (Material Handling and Equipment Distributors Association).
Who Uses Equipment Run-Hour Tracking
Run-hour tracking fits:
- Forklift dealers and service departments
- Rental equipment fleets
- Material handling and warehouse equipment
- Construction and grading equipment
Forklift Fleets, Inspections and Utilization
Forklifts rarely leave a property, so the questions are less about where they are on a highway and more about which yard, which customer site and how many hours they have worked. Dealers and rental operations often have units spread across many customer locations. A hard-wired tracker that reports location and run hours turns that spread-out fleet into one list you can sort by site, hours since service and idle time.
What OSHA expects from forklift operators
OSHA’s powered industrial truck standard, 29 CFR 1910.178, requires that trucks be examined before being placed in service, at least daily, and after each shift where they run around the clock. It also requires operator training and an evaluation of each operator’s performance at least once every three years. Tracking does not replace those inspections or that training, but run-hour data shows which units are actually in use and when, which helps managers confirm that daily checks are happening on the trucks that need them.
Billing and service from real hours
Rental and lease agreements are often written around hours of use. GPIO inputs on the AS11 read ignition and run-hour signals directly, so billing does not depend on a customer reading an hour meter. The same hours drive preventive maintenance: once a unit reaches its interval, the data is already in the platform and can flow to Fleetio for scheduling.
Theft and unauthorized moves
Material handling equipment is valuable and easy to load on a trailer. Geofences around customer sites and your yard, combined with tamper alerts and the AS11’s internal backup battery, give you notice if a unit is moved or a tracker is disconnected.
How MFS Sets Up a Forklift Fleet
Installs are done at your depot or on site:
Hardwire and map inputs
MFS installs the AS11, connects ignition and run-hour inputs and adds door or tilt sensors where needed.
Commission and verify
Each unit is tested so location and hours report correctly before it goes back into service.
Build your reports
Hours by unit and site, idle time, service due and movement alerts, sent to service, billing and management.
Sources
Regulatory summaries are general information, not legal advice. Check the current rule text for your operation.
See it working on your fleet
Tell us what you run and we’ll match the right hardware and reporting to how your business operates.
How Equipment Tracking Fits Into a Complete Fleet System
Run hours matter most when they drive maintenance and billing.
Equipment tracking is often combined with:
Heavy Equipment GPS Tracking
Runtime hours and movement alerts.
Learn more →Fleet Maintenance Tracking
Service reminders based on engine hours.
Learn more →Integrations & Open API
Fleetio, Fleetyr and custom dashboards.
Learn more →Together they show where each unit is, how hard it has worked, and when it is due.
View All Fleet ServicesHow are forklifts tracked?
Medium to heavy equipment such as forklifts uses wired asset trackers, so you can monitor location and run-time hours for billing your customer and scheduling maintenance.
Which tracker do you install on forklifts?
The AS11 hard-wired LTE asset tracker is engineered for wired, permanent installs on excavators, forklifts, haul trucks and other heavy assets, with GPIO inputs for ignition and run-hour sensing.
Can run hours drive service reminders?
Yes. Wired asset trackers can monitor engine or run-time hours on heavy equipment like excavators and forklifts, and Fleetio integration enables preventive maintenance scheduling and reporting.
Is MFS part of the material handling industry?
Yes. Mobile Fleet Solutions is a member of MHEDA (Material Handling and Equipment Distributors Association).




